i have a a ford truck bed liner that is plastic, it is at the road last week the garage wouldnt not take it- trash comes today, if you want it its yours. the sticker on it says F-SERIES SUPERDUTY FORD 1997- missing screws. please no emails just drive by, 8003 bluebonnet road in prp Location: prpits NOT ok to contact this poster with services or other commercial interests

block (cleaned) , heads (cleaned) , crank (been turned 10 - 10) needs 2 rods the other 4 are good.Good deal if someone is looking to re-build motor $500.00 Call Anthony 502-835-0334 leave message and I will call you back ASAP. Location: Louisville/PRPits NOT ok to contact this poster with services or other commercial interests

2004 STOCK Colorado aluminum wheels. Great shape with tires that have 70% left! Wont last. $400 FIRM Location: PRPits NOT ok to contact this poster with services or other commercial interests

SBC Accel distributor with Accel High power coil. also comes with 8mm Accel wires. Ready to roll. $135 Location: PRPits NOT ok to contact this poster with services or other commercial interests

chrome four barrel carb. 600 or 650 cfm, not sure. It works and ready to go. $55 Location: PRPits NOT ok to contact this poster with services or other commercial interests

SBC polished intake. Needs to be cleaned BAD. First 55 takes it. No low balls. FIRM Location: PRPits NOT ok to contact this poster with services or other commercial interests

ATTN RESTORERS-GENUINE GM Sheet metal off a 68 Camaro- Standard model convertibleIncludes following:RH & LH Fenders with ExtensionsRH & LH Fender SkirtsUpper Header PanelLower Valance PanelRadiator Core SupportNOTE: DOORS HAVE BEEN SOLD!!!These were removed from my project car which is undergoing a restoration for show. Rather than address existing defects and previous bodywork, I opted to replace all the sheet metal.These are perfect for someone looking to replace severely rusted or dented metal with minimal cost & re-work. Save BIG $$$...OEM GM parts would run big $. ORIGINAL Muscle Car parts like these are hard to find!!!Reproduction parts pricing alone for the remaining parts is over $1100 (not including shipping)Save over 50% from that amount...First Come First Served!!!My cars coming back from paint & these have gotta go!!!Parts are individually boxed!May consider separating but at a higher per item price. Prefer to sell as a whole set! PRICED TO GO!!!!Call: 502-417-53280900-2100Leave message if no answer! Location: PRPits NOT ok to contact this poster with services or other commercial interests

ATTN RESTORERS-Complete L-6 Engine & 350 Turbo TransmissionCorrect Coding on BOTH engine & Transmission for 68 CamaroA steal if looking for a code correct restoration!Very good conditionCall 502-417-53280900-2100hrsIf no answer leave message & I will get back to you! Location: PRPits NOT ok to contact this poster with services or other commercial interests

lambo doors for a 99 civic or sotxt (502)558-7401 Location: prpits NOT ok to contact this poster with services or other commercial interests

I have a nice grill Guard bumper for a 99 ram still on my truck come and take a look call 502-262-4332 Thanks !!!!! $150 Location: Louisville PRPits NOT ok to contact this poster with services or other commercial interests

I just took these wheels off of my 2004 F-150. only because I put a set of 22’s on it.The wheels are 20\" and tires are 285/50/r20 and are in excellent shape and are ready to be bolted on. My truck Has a six lug bolt pattern, but the rims have 12 holes, so there universal and will fit more Vehicles. They have Eagle GT tires, with a lot of tread left. The price for the wheels and Tires is just over $1700 retail, but I’m only asking $800 because that’s what I needed to Get my 22’s. Very clean and well taken care of, no pits. Wheel locks and key are also Included. GREAT DEAL! EXCELLENT CONDITION! DON’T MISS OUT! Location: prpits NOT ok to contact this poster with services or other commercial interests

This is a Heavy Duty Truck Transmission Jack. It is 4 foot long & 2 Foot Wide With Adjustable Platform. Made in the USA. Rises to 32 Inches Tilts Left, Right, Forward & backward. Has steel casters. The Pictures are not my best but with the lighting in the shed I can not get much better. Paint is in good shape. $200.00 or the best offer. If you are interested or have any questions please call Steve or Shirley at 502 448 6903 . Location: PRPits NOT ok to contact this poster with services or other commercial interests

For sale is a 69 and earlier beetle muffler It is new with pipes. May fit other years not sure. 100.00Also I have a set of heat exchangers for about the same years. 100.00

I have a 39 chevy 2 door sedan frame that is in need of a ney home other than my behind my garage. It is a roller. One front hub is missing and the drums other than that it is complete.Thanks for looking

im selling my type r they havent been ran hard at all i hardly drive my car now bc of winter so i need to sell themtxt me5025587401

make a offer and ill probably accept it...i am open to trades and cash is something ill never turn down...it is in very good condition...worth over 400...jus make a offer and u never kno i might accept it...call 502-544-8792 chris or email chris1216@insightbb.com

Jensen Multimedia AM/FM/DVD /CDC/MPC/WMA Receiver with motorized 7\" Wide Screen Display. 160 WATTS PEAK. was used one summer and sold Blazer. This unit works great and has plenty of power and bright screen resolution.This is a single dim. Serious inquires only.Call: 502-640-7742